 |
| |||||
|
| ||||||||||||
Convair Air Cored Inductor 0.36mH 38mm OD 0.9mm wire
► Made in the UK
► Air cored
► Wire diameter: 0.9mm²
► Inductance: 0.36mH (±3%)
► Overall Diameter: 38mm
► Height: 20mm
► DC Resistance: 0.4Ω
► Program Power: ≈ 500W *
These inductors are manufactured in the UK from high quality copper wire, and measured individually to ensure a close match to specifications. Designed for use with Convair DIY Crossover PCBs and available in a range of values to suit standard crossover configurations. PCBs 9002 and 9003 are predrilled to accept the wires from the inductors, for direct soldering onto the PCB.
The inductors come in three sizes, large (70mm Outside Diameter), Medium (50mm Outside Diameter) and small (38mm Outside Diameter).
The larger inductors are intended for low pass filters and the low pass section of a 2-way crossover. Larger inductors are usually made with 1.25mm² or 1.4mm² enamelled copper wire to ensure high power handling, although we do have some 0.9mm options for low-medium power applications.
The 38mm range of inductors are intended for high pass filters and the high pass section of a 2-way crossover. These small inductors are typically made with 0.9mm² diameter wire, which is sufficient for the power handling requirements of typical High Pass filter applications. For values above 0.4mH, smaller diameter wire (0.5mm² or 0.75mm²) may be used.
We are able to build to order most common value inductors between 0.1mH and 7mH, subject to limitations of bobbin size and wire diameter. Please email the sales office
* System Program Power. To avoid thermal overload, the program power (approx. 2 x AES Power) of the circuit should be less than 500W. For higher powered filters inductors using 1.25mm diameter copper wire are recommended.
► Air cored
► Wire diameter: 0.9mm²
► Inductance: 0.36mH (±3%)
► Overall Diameter: 38mm
► Height: 20mm
► DC Resistance: 0.4Ω
► Program Power: ≈ 500W *
These inductors are manufactured in the UK from high quality copper wire, and measured individually to ensure a close match to specifications. Designed for use with Convair DIY Crossover PCBs and available in a range of values to suit standard crossover configurations. PCBs 9002 and 9003 are predrilled to accept the wires from the inductors, for direct soldering onto the PCB.
The inductors come in three sizes, large (70mm Outside Diameter), Medium (50mm Outside Diameter) and small (38mm Outside Diameter).
The larger inductors are intended for low pass filters and the low pass section of a 2-way crossover. Larger inductors are usually made with 1.25mm² or 1.4mm² enamelled copper wire to ensure high power handling, although we do have some 0.9mm options for low-medium power applications.
The 38mm range of inductors are intended for high pass filters and the high pass section of a 2-way crossover. These small inductors are typically made with 0.9mm² diameter wire, which is sufficient for the power handling requirements of typical High Pass filter applications. For values above 0.4mH, smaller diameter wire (0.5mm² or 0.75mm²) may be used.
We are able to build to order most common value inductors between 0.1mH and 7mH, subject to limitations of bobbin size and wire diameter. Please email the sales office
* System Program Power. To avoid thermal overload, the program power (approx. 2 x AES Power) of the circuit should be less than 500W. For higher powered filters inductors using 1.25mm diameter copper wire are recommended.
Detailed specifications unavailable, please EMAIL the sales office for additional information.
| Other Convair Electronics products similar to Convair Air Cored Inductor 0.36mH 38mm OD 0.9mm wire: |
|
||
|
|